The first thing that you should know when building circuits for electrical devices are the theories in basic electronics. Get to know the various components used in them and how to properly connect them to each other. And study how to make and read schematic diagrams that represents graphically the electrical circuit using images and symbols.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
Circuit is closed if the path allows the electric current to pass through from a power source into the ground which usually indicates the device is turned on. An open one on the other hand breaks the path and would prevent movement such as when turning off machines. A switch is used in doing this so removing the source is not necessary when alternating between them.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Resistors are used to add resistance into circuits and reducing their current flow with ohms used in measuring its different values. They have also wattage ratings and the colored bands surrounding their body indicates their resistance value. You can learn these colored bands or search for graphs which helps calculate their values instead.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are components which are polarized allowing passage for currents in one direction and will cause voltage drop. One side of it is called cathode that connects to power while the other one is anode. These are just a few samples of some basic theories you shall learn for making electrical devices.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
Circuit is closed if the path allows the electric current to pass through from a power source into the ground which usually indicates the device is turned on. An open one on the other hand breaks the path and would prevent movement such as when turning off machines. A switch is used in doing this so removing the source is not necessary when alternating between them.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Resistors are used to add resistance into circuits and reducing their current flow with ohms used in measuring its different values. They have also wattage ratings and the colored bands surrounding their body indicates their resistance value. You can learn these colored bands or search for graphs which helps calculate their values instead.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are components which are polarized allowing passage for currents in one direction and will cause voltage drop. One side of it is called cathode that connects to power while the other one is anode. These are just a few samples of some basic theories you shall learn for making electrical devices.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment